Mechanical Engineering Project Topics with Materials:

ABSTRACT This write up is a detain of the process and formulation of plan for the physical realization of the construction of a mobile cooking system. It as divided into chapters, which discussed extensively the practical refrigerator cycle with attention given to constriction factors, working principle and choice of materials. The method used in... Continue Reading

PREFACE Our purpose of embarking on the construction of a project of this kind to present a very vivid and understandable fact that if given the necessary supports, that we the youths and engineers in potentials can more this country forward as regards to technical know how. Such a bird eye view right from time immemorial had proved that lot of... Continue Reading

ABSTRACT An electric popcorn machine is machine that is used to popcorn for human consumption. It uses electricity as it sources of energy, transfer it energy, that is used to pop the Corn. Also it has a stirrer, which rotate due to the convection of electrical energy from the source to mechanical energy in the motor, the stirrer tons the corn so... Continue Reading

ABSTRACT Parameters on which clear prints depends were comprehensively investigated. The study revealed that clear print depends on the impressed pressure the working temperature and the gold foil print paper life expectancy. Also studies were he manner of dependence of these parameters on prints impressed on sheets of varied thickness. The... Continue Reading

ABSTRACT. A machine for corn Sheller is highly and greatly needed for consistence of usage of corn in local and international levels. With regards to this indispensable need, a corn-shelling machine is designed which operates to remove the corn grains and leaving the cobs intact. In attainment to this design objective and aims, a proper... Continue Reading

ABSTRACT The aim of the project is to construct a domestic grain grinding machine to be powered by electric motor through pulley and belt transmission. The project is to perform mostly blending and grinding on grains e.g beans, maize, melon, millet and such other food crops. In construction of the project, there are various factors that is being... Continue Reading

ABSTRACT The candle molding machine is a vital device which cannot be done without, in any nation. This is because of the indispensable role candle plays, especially when there is no either source of light. In order to enhance adequate supply to both urban and rural consumers, the production of a candle molding machine is important. The major... Continue Reading

ABSTRACT Stop clocks are devices for indicating time duration for the occurrence of two events after a passage of time. They are usually powered by batteries and they measure time in unit of seconds. Most clocks stop working as a result of the inability of the main spring to make a complete revolution. Also problems that do arise in clocks and... Continue Reading

ABSTRACT The project work “Construction of standard steel cupboard” was constructed at the mechanical workshop. During the construction, various hand and machinery tools (equipment) such as electric welding machine, hammers, guillote, folding machine, spraying machine, milling machine, steel rule, hard saw, center punch, scribbers,... Continue Reading

ABSTRACT The sets of seizes with shocker which was fabricated and assembled in the chemical engineering pilot plant was aimed at providing the students with a machine that will aid them in practical involving the separation of solid particles. Besides this, it was also fabricated sizes or diameter of the solid particles of a substance by allowing... Continue Reading

ABSTRACT The aim of this project was to construct shell and tube heat exchanger with fixed boundless. A heat exchanger that would cool 5 x 5 x 10 – 3 kg/s of steam at a calculated heat load of 152 – 395/S was fabricated. The steam is to reach the heat exchanger from a distillation column at a temperature of 300k. The specification of... Continue Reading

ABSTRACT Propeller agitator is a specialized of various types of substances. It consists of three basic components which are the shaft, blade and the vessel. In the construction, mild steel was chosen due to it’s inherent properties. After the procurement, the following constructional operations were carried out which included marking out,... Continue Reading

ABSTRACT This project is concerned with the fabrication of as a single face pressurized kerosene cooker. The report shows the possible way in which the above mentioned can be designed, fabricated and maintained. Its also shows the strength and properties of the materials it is made of. Defects of the equipment can come through inability to... Continue Reading

ABSTRACT This work on the construction and fabrication of a mobile deep freezer revolves around the concept of refrigeration. The concept of refrigeration revolves around the reverse Carnot cycle. This is a cycle involving isentropic expansion (at the throttling valve), isothermal expansion (at the evaporator), isentropic compression (at the... Continue Reading

ABSTRACT Mechanical Engineering Department of the named Institute has many non – operational malhiues. Sequel to the fact, maintenance was poorly excuted which resulted to the breakdown deep freezer. Quality and effectiveness of machine maintenance were well observed. Also, a minimized maintenance and a highly successful repair was adopted.... Continue Reading

ABSTRACT Books are used recoding of what is happening or event that has already taken place which can be storing information it is useful and for the information that such books contained not to cost it support to be properly kept and these can be done when those books are kept in a cool dry place and a place free from rodents and insects attacked... Continue Reading

ABSTRACT This work is an attempt evolve a quicker and easier method of achieving Transportation. This will no doubt save considering human labour and time wasted involved in traditional manual method of transportation. To achieve this, preliminary experiment was first carried out to determine the optimum speed of the motor vehicle. Various design... Continue Reading

ABSTRACT This work investigated the variation of top loss heat transfer coefficient with the emittance of the absorber plate, the collector tilt angle and air gap spacing between the absorber plate and the cover plate. The effects of the emittance of the absorber plate, the collector tilt angle and air gap spacing between the plate and the cover... Continue Reading

ABSTRACT This is an abstract on the construction of a packed distillation column. A packed distillation column is used in the separating process distillation that is the separation of two miscible liquids. It was constructed by marking out the dimension of the column, condenser, pot, using steel rule scriber, oxyacetylene flame was used for... Continue Reading

ABSTRACT Wheelbarrow is a simple machine, which belong to the second-class lever. This is because the load or resistance is placed between the effort and the fulcrum. It is used in many areas of work to convey loads that are too heavy or bulky to be carried by hand. Wheelbarrow can be used as farm equipment, industrial equipment among others.... Continue Reading

ABSTRACT The constructional project involved the construction of an industrial barrow of standard size was constructed. The process used went across various Engineering practice. These involved the procurement of galvanized steel of 0.00mm to 300mm thickness. Some galvanized steel rods and pipes were also used for the construction. The Engineering... Continue Reading

ABSTRACT The project title “fabrication of flow nozzle” was done by a selected group of Engineering Students and the practiced objective (aim) of the project was centered on constructing a nozzle that is capable of transporting fluid from one to the other, to determine the charge in velocity of the moving fluid across two given areas... Continue Reading

ABSTRACT A book shelve is a structure which here series of compartments for the preservation of books, valuable or useful materials, which are made up of metal, wood or plastic materials of construction. (Engineering materials). The book shelve was constructed in the institute. (I.M.T Enugu). However, before the construction, two standard metal... Continue Reading

ABSTRACT This project is a fabrication of a standard drawing writing desk using the cheapest, effective and most readily available materials. Method of maintenance and services were also taken into consideration. The functional aspect of the equipment was also given adequate consideration in the project work. Also take into consideration the... Continue Reading

ABSTRACT The need for an authentic and reliable report relating to the repairs and rehabilitation of a faulty air-conditioner is inevitable. Many homes and offices uses the air-conditioner to cool he temperature in their respective homes. So the maintenance of the air-conditioner should be a top priority of every individual in order to avoid huge... Continue Reading