Electrical Engineering Project Topics with Materials:

ABSTRACT  As technological advancement has been on the increase in our society many have fallen in love with technology and world want to have a feel in virtually  to every thing they do. A design has been made in combination of electrical and electronics to change over from one power sources to the other automatically and trip off generation... Continue Reading

ABSTRACT As the zeal for change over on public power supply and stand- by generator increases; Engineers have researched deeply into the different ways and methods of achieving power changeover both manual and automatic types. It may no be considered as serious issue in some places where supply is up to 90% constant or where intermittent outage... Continue Reading

ABSTRACT  This project write up of a step – down transformer from 220v to 24v:12v, this is to expose what a transformer is all about and its important and uses. The aim of the project, step-down transformer is to show Electrical and Electronics Engineering, could step-down the voltage from 220v to 24:12v, and fro this project write up.... Continue Reading

ABSTRACT  This project work is on the construction of an F.M transmitter this system consists of four discrete modules namely the audio frequency (AF) amplifier (class A) the modulator the master oscillator and the radio frequency (RF) amplifier (ClassC) these formed the conventional events for building FM transmitter here the signal (from the... Continue Reading

ABSTRACT  The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories. This thesis describes the methodical approach to the design and construction of  any battery charger. However the procedure fro developed... Continue Reading

ABSTRACT   This project, 12v battery charge consist of few chapters, deal extensively with the design and construction of a batter charge which is capable of charging a 12v battery. The introductory chapter goes a long why in defining the battery charger and explanations of the mode of operations will be death with as we proceed.     TABLE OF... Continue Reading

ABSTRACT  The battery which has always serve as a sources of electrical current has in the past been invalid and inmost cases seen as monument after implicating as battery wound have to be brought over and over again the implicating has been that of lot of money is been spent for this purpose we give appraise for the advancement of technology... Continue Reading

 ABSTRACT  The construction of a 3-phase motor operation indicator exposes the techniques and skills employed in the construction of complex electrical circuit. The combination of contactors overload relay and other component to achieved the desired goal is diagrammatically and descriptively treated of practical knowledge     TABLE OF CONTENTS... Continue Reading

ABSTRACT  Audio loudspeaker (output transducer) is on of the most essential and powerful device used in telecommunication system. This is device capable of converting electrical signal into sound and vice versa. It is made up of few time of non-magnetic wire wound on a light cylindrical former that is mounted so that it can move freely insides... Continue Reading

ABSTRACT  Researchable lamp is a source of light that is generated from a D.C sources of supply this D.C sources is a battery that can also way be charged when it current and voltage ruse I decided to work on this as my project because its importance. It is very portable and help the a lot during night reading  It also serves as an immanency... Continue Reading

ABSTRACT Man has been so used to electricity that he cannot do without it. The absence of electricity causes a lot of sadness in our daily lives. Due to this reason I decided to work on a by rechargeable lamp as my project. The project is to see how one can construct a source of high without really generating is from an A.C source. I decided to... Continue Reading

ABSTRACT The main aim of any electric power supply in the world is to provide uninterrupted power supply at all times to all its consumers. Although, in developing countries, the electric power generated to meet the demands of the growing consumers of electricity is insufficient, hence power instability and outage. Power instability or outage in... Continue Reading

ABSTRACT-Power system planning is a vast and important issue for operation and expansion of power delivery. One of the basic objectives of planning is to determine the right schedule for investment in new devices which ensures secure and economic power delivery for predicted customer demand. System planning also addresses the question of reliable... Continue Reading

ABSTRACT In our present society, wireless communication has become most prevalent and mobile units (hand held devices /GSM/ Computers) are one of the most common equipments for conveying messages wirelessly. Owing to the fact that most youths in our society today on the average make use of at least one wireless device that communicate with other... Continue Reading

Abstract This project work was embarked on the construction and determination of the efficiency of 12 volts DC fan using two N3055 transistor, 1kΩ variable resistors, resistors, breadboard, veroboard, 12 volts DC battery and connectors at Science Laboratory Technological Department, Federal Polytechnic Offa, Nigeria. This is always required to... Continue Reading

The aim of this project is to shows the possibility of wireless power transfer through the design of a wireless charging pad.  In this project write-up, the methodology and principle of operation is wireless power transfer through inductive couple, a feasible design is modelled accordingly. The inductive couple technique is used because it is the... Continue Reading

Abstract This project work centered on construction of 12V/10A solar charge controller that is needed in photovoltaic system to safely charge regulate and discharge of sealed lead acid battery through DC load. Solar charge controller is devices that regulate solar photovoltaic power and prevent overcharging, over discharging or overflow of current... Continue Reading

ABSTRACT The Airbeetle-18 unmanned Aircraft is an Aircraft design for the purpose of surveillance following the fact that the parent Airbeetle-18 has almost reached the end of its life time. Hence, there is need to convert it to an unmanned aircraft in other to extend its service life time. A comprehensive literature review was carried out on... Continue Reading

TABLE OF CONTENTS Page ABSTRACT ……………………………………………………………………………..iii ACKNOWLEDGEMENTS……..………………………………………………………..iv LIST OF ILLUSTRATIONS………………………………………………………….…vii SECTION 1.... Continue Reading

The household lighting cost accounts for 10% of the electric bill, changing the light bulbs effectively can reduce the long term energy costs significantly. In Nigeria, where less than one percent of the population has access to 24 hours of interrupted power supply there is a need for a complementary, renewable source of light which provides... Continue Reading

Abstract A smoke detector is a device that senses smoke typically as an indicator of fire or non- smoking zone.  In order to ensure human safety and safeguard property against fire in both domestic and commercial settings, different solutions for smoke detection have been developed, a comprehensive literature was carried out on smoke detector,... Continue Reading

ABSTRACT   Automatic voltage inverter is an important area in power system engineering.   It is the process of using a 12v DC from the battery to achieve a 220/230V AC through the help of oscillator, drivers, power transistors and transformer.   The stages are battery to oscillators, oscillators to drivers, drivers to power transistors then... Continue Reading

ABSTRACT The AVR is automatic voltage regulator and it is a device which is used to regulate or stabilize electrical power supply for electrical or electronic appliances        In this project, therefore, we are interested in the construction of this all important device. Furthermore, we shall discuss the techniques, processes, switching... Continue Reading

The energy generation and power consuming loads at Brass LNG facility located in Brass Island, Bayelsa State Nigeria were analyzed and compared with expected demand changes and means of minimizing cost and greenhouse gas emission were also proffered with wind and solar energy penetration into the overall power mix . The wind and solar hybrid power... Continue Reading

ABSTRACT This project is titled the construction of a DC to AC inverter system. It is constructing to meet up with the power demand in the offices and in homes in the absence of power supply from the power holding company of Nigeria, PHCN. In order words the device / item serves as a substitute for PHCN which almost monopolises the power supply to... Continue Reading