All Project Topics with Materials - Page 1498

ABSTRACT A temperature control apparatus an “Armfield model was refurbished. The methodology employed were to detect the pulty parts of the equipment especially in the sump where leakages were observed. In the repair, the water in the sump was drained off, corrosion and rusting in the tank were... Continue Reading
ABSTRACT The project was on the construction of a venturimeter. Venturimeter being a measuring instruction was used in determining the flow rate of fluid down a pipe or the rate of discharge in a pipeline and is often fixed permanently at different sections of the piple line to know the discharge there. The research... Continue Reading
ABSTRACT Water Purification Unit or filtration unit is designed in way that it will give a nice result. Like in our filtration, we have sand and carbon filter that were responded to separate the suspended solid particles, odour and taste of the water, which will give a very nice filtered water at the end of the filtration.... Continue Reading
ABSTRACT In this research project, the various nail were subjected to six environments so as to check the effect of the environments on corrosion of the nails. Two sets of nails were used; normal nail and concrete nail. Six of each type while the other not coated. The research was carried out in the physical... Continue Reading
ABSTRACT The main area covered by this project was a research into the desirability of using locally obtained rubber later as loinder in paint manufacture. Considering the huge amount of money being spent on the importation of PVac (Poly vingl acetate) which is widely used as... Continue Reading
ABSTRACT This project was done to bring to lime light the appropriate method of solid waste handling, separation and utilization, in order to reduce the impact on the environment – environmental degradation. In this work, effort was made to point out the required steps taken in solid waste management.... Continue Reading
ABSTRACT The topic of this project is the “selection of lubricating oils for varied engines performance”. The aim is to specify the adequate lubricating oils for different engines. Using some equipment like hydrometer, flash point tester, and visometer, the proportion of lubricating... Continue Reading
THE CONSTRUCTION OF SIEVE ANALYSIS EQUIPMENT ABSTRACT The sets of seizes with shaker which was fabricated and assembled in the Chemical Engineering pilot plant was aimed at providing the students with a machine that will aid them in practical involving the separation of solid particles, besides, this, it was also fabricated sizes or diameter of... Continue Reading
ABSTRACT This research work was aimed at determining the effect of storage on unrefined vegetable oil. In the course of this research work, palm oil was used as a sample to determined the effect of storage to unrefined vegetable oil. A storage on interest was developed on this research work to have... Continue Reading
ABSTRACT This seminar was carried out with the sole aim of knowing the effects of the action of soap and detergent on soil/dirty substance during washing. It was found out that soap and detergent are water – soluble sodium or potassium salt of fatly acids... Continue Reading
THE POTENTIALS FOR A CO-OPERATIVE THRIFT CREDIT SOCIETY IN A HIGHER EDUCATION INSTITUTION (A CASE STUDY OF I.M.T, ENUGU) TABLE OF CONTENTS CHAPTER ONE 1.1 Background of the study/Introduction 1.2 Statement of Problem 1.3 Purpose of the Study 1.4 Scope of the Study 1.5 Significance of the Study 1.6 Definition of Term 1.7 Research Questions. CHAPTER... Continue Reading
ABSTRACT This project was carried out using bituminous coal (non activated) and the degree of refining of palm oil at different temperature and time using spectrophotometer. This was carried out to check the effectiveness of bituminous coal sample (bleaching earth) as a bleaching agent for... Continue Reading
ABSTRACT The project was carried out to produce slow burning candle for domestic uses. The project was carried out using the following apparatus; Reactor [20 litres in volume], bussen, Beaker (400ml) and wick. The chemical/raw material used in the production are wax, wick, cathyl alcohol, white colourant and... Continue Reading
ABSTRACTS This project was aimed at producing a fine high quality toilet soap at a low cost which will be of used to home and commercial purposes. The toilet soap produced has its major components caustic potash, palm kernel oil... Continue Reading
ABSTRACT It is generally known that cement id produced from limestone, mar/clay and gypsum by the following three basic process- wet semi- wet aid dry process. The cost of exploiting the limestone: the major raw material constitute about 50% of the production cost which results in the high cost... Continue Reading
ABSTRACT A mould can generally be defined as a pattern constructed for the production of the same shape and size. The constructional material differs from one operation to another. When one considers the money at hand, he decides whether to start from the primary production level or secondary... Continue Reading
ABSTRACT The tremendous (large) demand of some petroleum fractions in our modern world today has drive some professionals (experts) in oil sectors into exploration and drilling operation which is aimed at locating the mineral oil deposit and extracting it from beneath the earth surface with aid of some... Continue Reading
ABSTRACT This project “Extraction of oil from a local seed (groundnut oil) and Characterization” was carried out using ten cups of groundnut seeds that was purchased from a local market in Enugu metropolis. The oil these seeds were in Enugu using solvent extraction... Continue Reading
ABSTRACT The production of cassava flour by the method of traditional processing method (sun drying) and modern processing method (oven drying) was carried out using cassava sliced cubes or peeled cassava. Indeed, the traditional Nigeria techniques of... Continue Reading
ABSTRACT This project is on the production of paint from the available materials. The first process involved was the sourcing of the available material which include calcium carbonate (dotonute) water etc. the next step is the proper production procedure. The same product patterns was... Continue Reading
PRODUCTION OF BLACK AND BROWN POLISH BROWN POLISH ABSTRACT This project is aimed at producing black and brown polish of good quality. For clearity, polish is a substance rubbed on the surface of materials to make them smooth and shiny. Polish has being of immense importance in protecting leather surfaces and enhancing their beauty. To produce a... Continue Reading
ABSTRACT The project Analysis of Enugu Coal was done to determine the characteristic properties of Enugu Coal with particular emphasis on the proximate and ultimate analysis. Coal samples from the Enugu Coal (Onyeama) mine were obtained and pulverized. The coal sample (pulverized) was subjected to proximate and ultimate... Continue Reading
ABSTRACT This project is on the production of paint from the available materials. The first process involved was the sourcing of the available material which include calcium carbonate (dotonute) water etc. the next step is the proper production procedure. The same product patterns was... Continue Reading
ABSTRACT This research project was carried out principally for the production of liquid and vapourized perfumes from local raw materials. The local raw material were subjected to various processing conditions in order to obtain purified perfume. The methods generally used in this work include expression... Continue Reading
ABSTRACT This project was Carrie lent using sub-bituminous coal and crude palm oil. The degree of bleaching of the palm oil was monitored with a spectorphoto meter. The coal was collected in a lump from the mine. It air-chiecl to removed the moisture content and thereafter, size reduced to a... Continue Reading