Explore Project Topics on: mechanical

ABSTRACT This project is designed to determine households' access to domestic water supply via mechanical and  non-mechanical energy system in Usin, Ikole local government area Ekiti State Nigeria, in terms of  quality and quantity as the importance of adequate safe water supply to human health cannot be over  emphasized. However, safe/improve... Continue Reading

ABSTRACT The main aim of the research is to study the mechanical properties of concrete and heir effects in concrete stability and failure. He fractures mechanical properties in particular uniaxial tensile strength Ft, young’s modules Eo and fractures energy Gf as sell as the shape of the stress strain and the stress- deformation relation  were... Continue Reading

ABSTRACT The main aim of the research is to study the mechanical properties of concrete and heir effects in concrete stability and failure. He fractures mechanical properties in particular uniaxial tensile strength Ft, young’s modules Eo and fractures energy Gf as sell as the shape of the stress strain and the stress- deformation relation  were... Continue Reading

TABLE OF CONTENTS Title Page i Certificate of Approval ii Dedication iii Acknowledgment iv Abstract v Table of contents vi 1. FRACTIONAL ORDER CALCULUS 2. FUNCTIONS OF FRACTIONAL CALCULUS 2.1 The Gamma function 3 2.2 The Beta Function 5 2.3 The Mittag-Leffler Function 5 2.4 Laplace Transform 7 2.5 The Convolution Theorem 9 2.6 Riemann-Liouville... Continue Reading

see deeper... Continue Reading

see deeper... Continue Reading

PREFACE A new machine/equipment will provide satisfactory service if kept in proper operating condition. The inevitability of less than 100% reliability of any machine/equipment after some period and maintenance. Also in system of any complexity, certain replacement adjustments are... Continue Reading

ABSTRACT This project is concerned write the identification of those defects that are found in most of the drawing tables in the Mechanical Engineering drawing studio. The report investigates the possible ways through which the mentioned above can be brought back to normal standard for usage... Continue Reading

PHYSICAL AND MECHANICAL PROPERTIES OF NERICA PADDY                                                       CHAPTER ONE 1.0 INTRODUCTION: 1.1 RESEARCH BACKGROUND: After harvest, agro raw materials are normally handled, transported, dried, stored... Continue Reading

ABSTRACT             This project is concerned write the identification of those defects that are found in most of the drawing tables in the Mechanical Engineering drawing studio.             The report investigates the possible ways through which the mentioned above can be brought back to normal standard for usage ins the... Continue Reading

CHAPTER ONE INTRODUCTION In this pass, cutting of grasses in the school, track or filed, Industries hotel, public centers, Agriculture lands etc. was done by machete or cutlass. This method of manual cutting not only was laborious but also time consuming as it is human effort that is entirely needed both for cutting and motion. There was also... Continue Reading

Abstract Synthetic biology is the engineering of biology; it is the evaluation and design of biological systems in a rational and systematic manner. It blurs the lines between various science and engineering disciplines due its numerous applications, with one of the most significant being the use of biosensors in environmental remediation.... Continue Reading

CHAPTER ONE 1.0 INTRODUCTION: 1.1 RESEARCH BACKGROUND: After harvest, agro raw materials are normally handled, transported, dried, stored and further processed into food, feed and fiber. In some basic post harvest activities, separation processes such as sorting, grading and cleaning are involved. In mechanized operations, these post harvest... Continue Reading

REPAIR OF DEEP FREEZER ABSTRACT This work gives an account of all activities carried out to restore a faulty and abandoned deep freezer to normal functioning. This report therefore contains the different stages embarked in the execution of the project. These include the literature back ground, checking’s conducted, cleaning, repair operations... Continue Reading

ABSTRACT This study investigation on the mechanical properties of Sagbama rice granite was analyzed to determine the load that would cause ultimate flexural stress on the material when used in concrete construction .This is necessary to make decision on where it is suitable for use. This study requires the production of 12 concrete beams of... Continue Reading

ABSTRACT This study investigation on the mechanical properties of Sagbama rice granite was analyzed to determine the load that would cause ultimate flexural stress on the material when used in concrete construction .This is necessary to make decision on where it is suitable for use. This study requires the production of 12 concrete beams of... Continue Reading

ABSTRACT This study investigation on the mechanical properties of Sagbama rice granite was analyzed to determine the load that would cause ultimate flexural stress on the material when used in concrete construction .This is necessary to make decision on where it is suitable for use. This study requires the production of 12 concrete beams of... Continue Reading

ABSTRACT    This study is designed to evaluate quality management in mechanical construction projects in the oil and gas industry. This evaluation was done by assessing quality assurance, quality control and planning. Three hypotheses were postulated to answer research questions. The study adopted an audit method as an appraisal strategy. To... Continue Reading

ABSTRACT In the mechanical engineering department of institute of management and technology there are many machines but it is not all that is functioning well. This may airless as a   result of lack of maintenance which is a prove in the breakdown of the air conditioner. The quality and effectiveness of materials were mated very well as referred... Continue Reading

ABSTRACT Steel is arguably the world’s most ‘advanced” material. It is a very versatile material with a wide range of attractive properties which can be produced at a very competitive cost. It has a diverse range of applications, and is second only to concrete in its annual production tonnage. Steel is not a new invention which leads to a... Continue Reading

ABSTRACT  Mechanical Engineering Department of the named Institute has many non – operational malhiues. Sequel to the fact, maintenance was poorly excuted which resulted to the breakdown deep freezer. Quality and effectiveness of machine maintenance were well observed. Also, a minimized maintenance and a highly successful  repair was adopted.... Continue Reading

ABSTRACT Mechanical Engineering Department of the named Institute has many non – operational malhiues. Sequel to the fact, maintenance was poorly excuted which resulted to the breakdown deep freezer. Quality and effectiveness of machine maintenance were well observed. Also, a minimized maintenance and a highly successful repair was adopted. In... Continue Reading

ABSTRACT Mechanical Engineering Department of the Institute of Management and Technology has many non – functional machines. This is caused as a result of poor maintenance culture, which in turn resulted to breakdown of the Deep Freezer under review.... Continue Reading

AbstractThe main purpose of the project is to convert polyethylenetetraphylate (PET), a known plastic waste material in Ghana, to wealth. Composite samples were produced by heating aggregates together with shredded PET plastic waste material, while bitumen was added to the plasticcoated aggregates. The composites produced were of 4.5 wt%, 9.0 wt%,... Continue Reading

The household lighting cost accounts for 10% of the electric bill, changing the light bulbs effectively can reduce the long term energy costs significantly. In Nigeria, where less than one percent of the population has access to 24 hours of interrupted power supply there is a need for a complementary, renewable source of light which provides... Continue Reading

ABSTRACT The design of a 1000 tonnes per annum Shea butter plant was carried out using data obtained from literature. Assumptions were made, where experimental data were not available. The block diagram, process flow sheet, material and energy balance on the process was carried out and presented on this work. A total of six units were used in the... Continue Reading

The household lighting cost accounts for 10% of the electric bill, changing the light bulbs effectively can reduce the long term energy costs significantly. In Nigeria, where less than one percent of the population has access to 24 hours of interrupted power supply there is a need for a complementary, renewable source of light which provides... Continue Reading

It's a journal that explains the design of a shea butter plant.... Continue Reading

ABSTRACT The effect of Heat treatment on the Mechanical Properties of a welded joint of medium carbon steel has been carried out. The materials were cut, welded, to get 27 samples needed. Thereafter, Heat Treatment was carried out on the samples. Then the specimens were grouped into two groups, group A and group B. In group A, after the heat... Continue Reading

ABSTRACT Metal Matrix Composites (MMC’s) have evoked a keen interest in recent times for potential applications. Composite materials like Particle-reinforced Aluminium Silicon carbide (Al/SiC) Metal-Matrix Composite is gradually becoming very important materials in manufacturing industries e.g. aerospace, automotive and automobile industries due... Continue Reading